Build 63% done. The X10 panels arrive on 21 November.

Cleaning robot for rooftop solar rows

ASH keeps a rooftop row of five 650 W panels clean on its own. It sprays, brushes, parks and recharges from its own solar panel, so nobody has to climb onto the roof.

The ASH robot: two navy steel blocks joined by two long aluminium T supports, a small solar panel on top

A clean row in two and a half minutes. Five panels, there and back, on its own.

  1. DockParks at the right end and checks the glass
  2. Spray14 nozzles wet the glass ahead of the brushes
  3. BrushTwo bristle strips sweep the glass behind them
  4. ReturnDrives back at 0.08 m/s and charges
The robot on a row of five large solar panels tilted at 30 degrees

Two sealed steel blocks carry everything it needs. The dust stays outside.

  • It thinks for itselfPlans each cleaning run, talks to your phone and stores the sun's charge
  • It brings its own water pressureSends water to the spray nozzles while it cleans
  • It reaches edge to edgeTwo long beams carry the brushes and nozzles across the whole panel
The robot's two blocks with their lids lifted, showing the boards, battery, pump and wiring inside

Wheels never touch glass

Four 75 mm wheels run on the aluminium lip of the panel frame, and rollers under the frame flange hold the robot down in wind.

Both lower drive wheels standing on the aluminium lip of the panel frame, seen side-on from the glass; the glass itself is untouched

Spray first, then soft bristles. About 1.85 litres a minute from each bank.

The lower block from below: a drive wheel, guide rollers and the T supports leaving it

Wet first14 spray points loosen the dust before a bristle touches the glass

Then sweepSoft bristles lift the loosened dirt across the full width of the panel

Then move onOne pass covers all five panels in about 70 seconds

Runs on sunlight. Its own 50 W panel recharges it in about 2.5 hours.

  • Cleaning runs a charge19
  • Days without sun, one run a day5.8
  • Stored sunlightIts battery fills from the panel on its back, so cloudy days do not stop it43.2 Wh
The robot from above, its 50 W solar panel mounted across the two T supports

Build progress. Updated 20 November 2026.

  • Design80%CAD, calculations, FEA and the CNC files are done; the water lines are next.
  • Electronics100%Every board, motor, sensor and cable is bought.
  • Structure40%Both blocks are cut on the CNC and bent; welding is next.
  • Solar panels33%Two LONGi X10 panels arrive on 21 November.

A percentage counts the finished steps; a step under way counts half. See every step.

The team. University of Technology, Iraq.

  • Ahmed Safaa ShabanStudent
  • Shahad Alaa Al-Dien SalimStudent
  • Hasanien Fouad RidhaStudent
  • Dr. Sattar AljabairSupervisor, General Mechanical Engineering

Specifications.

The robot from straight above: two navy blocks joined by two long T supports, the 50 W panel between them

Performance

Row cleaned
5 panels, 3.25 kW
One pass
5.78 m in about 70 s
There and back
about 2.5 min
Travel speed
0.08 m/s

Power

Battery
43.2 Wh, filled by its own panel
Cleaning runs a charge
19
Recharge from its own panel
about 2.5 h
Days without sun
5.8, one run a day

Smart

Control
From your phone, over Wi-Fi
Dirt check
Looks at the glass from its dock
Glass temperature
Read at the dock
Standby
Sleeps between runs, stays reachable

Build

Length
2.60 m
Body
Rust-resistant steel and aluminium
Drive
Four-wheel drive on the panel frame
Fits
Panels at 30°, 20 mm gaps

Figures are calculated from the CAD model and the design; ASH is being built now and has not been measured yet.